move configuration folder

03-cura/01-configuration/variants/flsun_v400_0.4.inst.cfg

@@ -0,0 +1,159 @@
+[general]
+name = 0.4
+version = 4
+definition = flsun_v400
+
+[metadata]
+setting_version = 23
+type = variant
+hardware_type = nozzle
+
+[values]
+# Global Settings, valid for all
+# Printing with a 0.4 nozzle size
+machine_nozzle_size = 0.4
+
+# This printer is using Klipper Firmware Acceleration control, Jerk control, Retraction and Input Shaping is done by the
+# firmware and does not need to be done by Cura.
+# - enable hardware retraction with G10/G11
+machine_firmware_retract = True
+klipper_retract_length = =retraction_amount
+klipper_retract_prime_length = =retraction_extra_prime_amount
+klipper_retraction_speed = =retraction_speed
+klipper_retract_speed = =retraction_retract_speed
+klipper_retract_prime_speed = =retraction_prime_speed
+# - disable cura acceleration and jerk control
+acceleration_enabled = False
+jerk_enabled = False
+
+
+# Quality
+
+
+# Walls
+wall_distribution_count = 2
+wall_0_wipe_dist = =machine_nozzle_size * 2
+optimize_wall_printing_order = True
+# wall oder
+inset_direction = inside_out
+# print thin walls
+fill_outline_gaps = True
+z_seam_type = sharpest_corner
+
+# Top/Bottom
+# extra skin wall count
+skin_outline_count = 2
+
+# Infill
+infill_sparse_density = 15
+infill_pattern = ='gyroid' if infill_sparse_density < 80 else 'zigzag'
+infill_wall_line_count = 1
+connect_infill_polygons = True
+skin_edge_support_layers = 2
+
+# Material
+material_print_temperature = =default_material_print_temperature
+# Already start printing when reaching this temperature, we will still have some time to heat up
+# while printing the waste lien and the skirt / brim
+material_initial_print_temperature = =default_material_print_temperature - 10
+# first layer
+material_print_temperature_layer_0 = =default_material_print_temperature
+# Cool down the nozzle when a nozzle switch or standby is expected to happen
+# Nozzle will reach this temperature at the exact moment of nozzle switch or standby start
+material_final_print_temperature = =default_material_print_temperature - 15
+# first layer
+material_bed_temperature_layer_0 = =material_bed_temperature
+
+
+# Speed
+# General Print Speed, somewhat good quality but still good speed
+speed_print = 150
+
+# Infill, can be printed faster
+speed_infill = =speed_print * 1.4
+
+# Walls print a little bit slower
+speed_wall = =speed_print * 0.8
+# outer wall, prioritize quality
+speed_wall_0 = =speed_print * 0.6
+# between outer wall and infill, maintain adhesion
+speed_wall_x = =speed_print * 0.8
+# top surface outer wall, slower for better finish
+speed_wall_0_roofing = =speed_print * 0.5
+# top surface inner wall, sligthly faster than outer wall
+speed_wall_x_roofing = =speed_print * 0.6
+# Top skin, slower to ensure smooth finish and layer bonding
+speed_roofing = =speed_print * 0.6
+# balance of flatness and time
+speed_topbottom = =speed_print * 0.6
+# support finish does not matter, but needs to maintin somewhat dimensional accuracy
+speed_support = =speed_print * 1.2
+# infill
+speed_infill = =speed_print * 1.2
+speed_support_infill = =speed_print * 1.2
+speed_support_interface = =speed_print * 0.8
+speed_support_roof = =speed_print * 0.7
+speed_support_bottom = =speed_print * 0.8
+speed_prime_tower = =speed_print * 0.7
+speed_travel = =speed_print * 1.5
+
+# Layer 0 always slow for good adhesion
+speed_layer_0 = 30
+speed_print_layer_0 = 30
+speed_travel_layer_0 = 60
+skirt_brim_speed = 30
+speed_z_hop = 10
+speed_slowdown_layers = 3
+speed_euqalize_flow_width_factor = 70
+
+# Travel
+retraction_enable = True
+retract_at_layer_change = False
+retraction_amount = 0.8
+retraction_speed = 30
+retract_retract_speed = =retraction_speed
+retraction_prime_speed = =retraction_speed * 0.7
+retraction_extra_prime_amount = 0
+retraction_combing = no_outer_surfaces
+retraction_combing_max_distance = 2
+travel_avoid_other_parts = True
+travel_avoid_supports = True
+
+# Cooling
+cool_fan_speed = 80
+cool_fan_speed_min = =cool_fan_speed
+cool_fan_speed_max = 100
+cool_min_layer_time_fan_speed_max = 20
+cool_fan_speed_0 = 0
+cool_fan_full_layer = 3
+cool_min_layer_time = 10
+cool_min_speed = 15
+cool_lift_head = True
+cool_min_temperature = =material_print_temperature - 15
+
+# Support
+support_brim_width = 5
+support_xy_distance_overhang = 0.5
+support_tower_diameter = 8
+support_angle = 60
+
+
+
+# Build Plate Adhesion
+prime_blob_enable = False
+adhesion_type = skirt
+skirt_line_count = 3
+skirt_gap = 3
+skirt_brim_minimal_length = 300
+
+# Mesh Fixes
+
+
+# Special Modes
+
+
+# Experimental
+infill_enable_travel_optimization = True
+wall_overhang_angle = 60
+bridge_settings_enabled = True
+