fix permissions across files

02-klipper/01-configuration/KlipperScreen.conf

@@ -119,6 +119,7 @@ extrude_speeds: 1, 2, 5, 10
 #~# --- Do not edit below this line. This section is auto generated --- #~#
 #~#
 #~# [main]
+#~# print_estimate_method = file
 #~# screen_blanking_printing = 1800
 #~# show_heater_power = True
 #~# move_speed_xy = 80
@@ -167,4 +168,7 @@ extrude_speeds: 1, 2, 5, 10
 #~# hyperlapse = False
 #~# test_stream_delay = False
 #~# timelapse_take_frame = False
+#~# security_offset = False
+#~# save = False
+#~# z_offset_calibration = False
 #~#

02-klipper/01-configuration/printer.cfg

@@ -61,9 +61,13 @@
 [include macros.cfg]
 #[include adxl345_pico.cfg]  #Enable if you want to use ADXL with Rapsberry Pi Pico
 #[include adxl345_fysetc.cfg]  #Enable if you want to use ADXL with Fysetc Portable Input Shaper
-[include timelapse.cfg]  #Enable if you want to use Timelapse
+#[include timelapse.cfg]  #Enable if you want to use Timelapse
 #[include neopixels.cfg]  #Enable if you want to use some Neopixels macros
 
+########################################
+# Enable Exclude Objects
+########################################
+[exclude_object]
 
 ########################################
 # Printer Settings
@@ -72,14 +76,14 @@
 [printer]
 kinematics: delta
 max_velocity: 600
-max_accel: 10000
+max_accel: 8000
 minimum_cruise_ratio: 0.5
 square_corner_velocity: 5
 max_z_velocity: 100
 max_z_accel: 1500
 minimum_z_position: -25
 print_radius: 152
-#delta_radius: 152
+delta_radius: 152
 
 
 ########################################
@@ -96,9 +100,9 @@ endstop_pin: ^PA15
 homing_speed: 50
 homing_retract_dist: 5.0
 homing_retract_speed: 10
-#angle: 210
-#position_endstop: 415.0
-#arm_length = 345.0
+angle: 210
+position_endstop: 415.0
+arm_length = 345.0
 
 [tmc2209 stepper_a]
 uart_pin: PD5
@@ -122,7 +126,7 @@ enable_pin: !PE1
 microsteps: 64  # If you encounter an error while measuring the resonances. Replace the microsteps to 16 just for the duration of the test.
 rotation_distance: 40
 endstop_pin: ^PA12
-#angle: 330
+angle: 330
 
 [tmc2209 stepper_b]
 uart_pin: PD7
@@ -146,7 +150,7 @@ enable_pin: !PB8
 microsteps: 64  # If you encounter an error while measuring the resonances. Replace the microsteps to 16 just for the duration of the test.
 rotation_distance: 40
 endstop_pin: ^PC4
-#angle: 90
+angle: 90
 
 [tmc2209 stepper_c]
 uart_pin: PD4
@@ -180,10 +184,10 @@ max_extrude_cross_section: 50
 max_extrude_only_distance: 800
 #pressure_advance: 0.04
 #pressure_advance_smooth_time: 0.040
-#control = pid
-#pid_kp = 17.501
-#pid_ki = 0.711
-#pid_kd = 107.630
+control = pid
+pid_kp = 17.501
+pid_ki = 0.711
+pid_kd = 107.630
 
 [tmc2209 extruder]
 uart_pin: PD9
@@ -193,7 +197,7 @@ stealthchop_threshold: 0
 
 [autotune_tmc extruder]  # Enable if Klipper TMC Autotune is used
 motor: flsun-v400-36
-tuning_goal: performance
+tuning_goal: auto
 
 
 ########################################
@@ -206,10 +210,10 @@ sensor_pin: PC0
 sensor_type: EPCOS 100K B57560G104F
 min_temp: -5
 max_temp: 120
-#control = pid
-#pid_kp = 64.044
-#pid_ki = 3.812
-#pid_kd = 268.984
+control = pid
+pid_kp = 64.044
+pid_ki = 3.812
+pid_kd = 268.984
 
 
 ########################################
@@ -242,12 +246,12 @@ heater_temp: 50.0
 pin: !PA11
 x_offset: 0
 y_offset: 0
-#z_offset: 0
+z_offset: 0
 speed: 10
 lift_speed: 50
 samples: 8
 samples_result: average
-sample_retract_dist: 10
+sample_retract_dist: 6
 samples_tolerance: 0.02
 samples_tolerance_retries: 7
 
@@ -385,127 +389,3 @@ value: 1
 #initial_RED: 1.0
 #initial_GREEN: 1.0
 #initial_BLUE: 1.0
-
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [probe]
-#*# z_offset = 17.828
-#*#
-#*# [endstop_phase stepper_a]
-#*# trigger_phase = 77/256
-#*#
-#*# [endstop_phase stepper_b]
-#*# trigger_phase = 254/256
-#*#
-#*# [endstop_phase stepper_c]
-#*# trigger_phase = 207/256
-#*#
-#*# [printer]
-#*# delta_radius = 162.002474
-#*#
-#*# [stepper_a]
-#*# angle = 209.973682
-#*# arm_length = 344.755561
-#*# position_endstop = 419.986098
-#*#
-#*# [stepper_b]
-#*# angle = 329.779050
-#*# arm_length = 344.988509
-#*# position_endstop = 420.533328
-#*#
-#*# [stepper_c]
-#*# angle = 90.000000
-#*# arm_length = 345.350100
-#*# position_endstop = 419.275934
-#*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	  -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722, -0.042722
-#*# 	  -0.103985, -0.103985, -0.103985, -0.103985, -0.092863, -0.041497, -0.029735, -0.024573, -0.009876, 0.303776, 0.303776, 0.303776, 0.303776
-#*# 	  -0.107217, -0.107217, -0.107217, -0.095680, -0.078747, -0.041636, -0.027165, 0.001847, 0.040765, 0.030959, -0.001207, -0.001207, -0.001207
-#*# 	  -0.020548, -0.020548, -0.030235, -0.045109, -0.047644, -0.013968, 0.004580, -0.022084, -0.040851, -0.010745, -0.072567, -0.046700, -0.046700
-#*# 	  -0.065225, -0.065225, -0.070452, -0.082613, -0.004947, -0.007693, 0.002972, -0.017327, 0.006928, -0.000043, -0.022182, -0.051542, -0.051542
-#*# 	  -0.015597, -0.015597, -0.024245, -0.016206, 0.017731, 0.011087, -0.007589, 0.014521, -0.014740, -0.055408, -0.078663, -0.128265, -0.128265
-#*# 	  -0.006361, -0.035030, -0.027430, -0.027100, -0.035687, 0.008191, 0.000000, 0.028685, -0.013501, -0.000669, -0.006836, -0.063614, -0.120604
-#*# 	  0.009006, 0.009006, -0.038215, -0.004862, -0.005067, 0.023846, 0.005303, -0.017008, -0.001132, -0.047883, -0.078197, -0.104467, -0.104467
-#*# 	  -0.065296, -0.065296, -0.094076, -0.050048, 0.005887, 0.029406, 0.012646, -0.001847, 0.042902, 0.015198, -0.038658, -0.069033, -0.069033
-#*# 	  -0.089840, -0.089840, -0.067392, -0.046851, -0.046780, 0.008230, -0.024958, 0.005470, 0.000727, 0.014177, -0.031855, -0.067485, -0.067485
-#*# 	  -0.142119, -0.142119, -0.142119, -0.132495, -0.062554, -0.045859, -0.002144, 0.021794, 0.012583, 0.032188, -0.027538, -0.027538, -0.027538
-#*# 	  -0.150265, -0.150265, -0.150265, -0.150265, -0.090845, -0.036079, -0.013544, 0.013161, 0.011777, 0.039157, 0.039157, 0.039157, 0.039157
-#*# 	  0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246, 0.005246
-#*# x_count = 13
-#*# y_count = 13
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.1
-#*# min_x = -147.0
-#*# max_x = 147.0
-#*# min_y = -147.0
-#*# max_y = 147.0
-#*#
-#*# [heater_bed]
-#*# control = pid
-#*# pid_kp = 71.685
-#*# pid_ki = 2.583
-#*# pid_kd = 497.313
-#*#
-#*# [extruder]
-#*# control = pid
-#*# pid_kp = 20.836
-#*# pid_ki = 1.187
-#*# pid_kd = 91.417
-#*#
-#*# [delta_calibrate]
-#*# height0 = 17.828
-#*# height0_pos = 128669.000,128669.000,128669.000
-#*# height1 = 17.828
-#*# height1_pos = 151185.800,151185.800,116034.600
-#*# height2 = 17.828
-#*# height2_pos = 126085.200,163987.400,126085.200
-#*# height3 = 17.828
-#*# height3_pos = 116703.400,147524.800,147524.800
-#*# height4 = 17.828
-#*# height4_pos = 125485.400,125485.400,152772.600
-#*# height5 = 17.828
-#*# height5_pos = 144289.000,117535.400,144289.000
-#*# height6 = 17.828
-#*# height6_pos = 158014.000,125724.800,125724.800
-#*# distance0 = 64.842
-#*# distance0_pos1 = 133621.315,134972.482,134563.893
-#*# distance0_pos2 = 125491.344,143400.833,143020.320
-#*# distance1 = 65.035
-#*# distance1_pos1 = 134001.019,134206.848,134948.991
-#*# distance1_pos2 = 131041.776,131235.496,149780.315
-#*# distance2 = 64.878
-#*# distance2_pos1 = 134766.662,133828.010,134563.893
-#*# distance2_pos2 = 143208.928,125698.066,143020.320
-#*# distance3 = 64.88
-#*# distance3_pos1 = 135152.650,134210.345,133798.242
-#*# distance3_pos2 = 149983.962,131287.939,130851.341
-#*# distance4 = 64.945
-#*# distance4_pos1 = 134768.441,134976.007,133417.655
-#*# distance4_pos2 = 143239.022,143460.477,125287.675
-#*# distance5 = 64.858
-#*# distance5_pos1 = 134002.784,135359.341,133798.242
-#*# distance5_pos2 = 131068.237,150190.619,130851.341
-#*# distance6 = 64.892
-#*# distance6_pos1 = 126122.444,141650.703,142514.843
-#*# distance6_pos2 = 131635.229,130719.895,149144.094
-#*# distance7 = 64.988
-#*# distance7_pos1 = 131709.573,130794.251,147886.148
-#*# distance7_pos2 = 143462.253,125909.898,142015.038
-#*# distance8 = 65.122
-#*# distance8_pos1 = 142705.473,126331.599,141267.714
-#*# distance8_pos2 = 149348.788,131881.624,130333.916
-#*# distance9 = 65.015
-#*# distance9_pos1 = 148090.827,131953.425,130406.602
-#*# distance9_pos2 = 142233.571,143711.016,125497.896
-#*# distance10 = 65.185
-#*# distance10_pos1 = 141485.169,142950.990,125919.593
-#*# distance10_pos2 = 130549.893,149552.325,131444.874
-#*# distance11 = 65.11800000000001
-#*# distance11_pos1 = 130621.733,148294.415,131518.365
-#*# distance11_pos2 = 125700.751,142395.888,143272.712

02-klipper/01-configuration/variables.cfg

@@ -1,3 +1,3 @@
 [Variables]
-zoffset = {'z': '0'}
+zoffset = {'z': 0.11}
 

03-cura/01-configuration/README.md

@@ -10,7 +10,7 @@
 - Auto-Orientation
 - Automatic Slicing Toggle
 - Material Cost Tools
-- Calibration Shapes
+- Calibration Shapes Reborn
 
 # Disable Cura Plugins
 

03-cura/01-configuration/definitions/flsun_v400.def.json

@@ -1,45 +1,80 @@
 {
-    "version": 2,
-    "name": "Flsun V400",
-    "inherits": "fdmprinter",
-    "metadata":
-    {
-        "visible": true,
-        "author": "FLSUN, Guislain Cyril, Frank Zechert",
-        "manufacturer": "Flsun",
-        "file_formats": "text/x-gcode",
-        "platform": "flsun_v400.stl",
-        "has_machine_quality": true,
-        "has_materials": true,
-        "machine_extruder_trains": { "0": "flsun_v400_extruder_0" },
-        "platform_offset": [
-            0,
-            -40.6455,
-            -43.5
-        ]
-    },
-    "overrides":
-    {
-        "gantry_height": { "value": "0" },
-        "infill_sparse_density": { "default_value": 15 },
-        "machine_center_is_zero": { "default_value": true },
-        "machine_depth": { "default_value": 300 },
-        "machine_end_gcode": { "default_value": "END_PRINT\n" },
-        "machine_head_with_fans_polygon":
-        {
-            "default_value": [
-                [0, 0],
-                [0, 0],
-                [0, 0],
-                [0, 0]
-            ]
-        },
-        "machine_heated_bed": { "default_value": true },
-        "machine_height": { "default_value": 410 },
-        "machine_shape": { "default_value": "elliptic" },
-        "machine_start_gcode": { "default_value": ";Nozzle diameter = {machine_nozzle_size}\n;Filament type = {material_type}\n;Filament name = {material_brand} {material_name}\n;Filament weight = {filament_weight}\n;M109 S{material_print_temperature}\n;M190 S{material_bed_temperature}\n\nSTART_PRINT BED_TEMP={material_bed_temperature_layer_0} EXTRUDER_TEMP={material_print_temperature_layer_0}\n" },
-        "machine_width": { "default_value": 300 },
-        "material_diameter": { "default_value": 1.75 },
-        "z_seam_type": { "value": "'sharpest_corner'" }
-    }
+	"version": 2,
+	"name": "Flsun V400",
+	"inherits": "fdmprinter",
+	"metadata": {
+		"visible": true,
+		"author": "FLSUN, Guislain Cyril, Frank Zechert",
+		"manufacturer": "Flsun",
+		"file_formats": "text/x-gcode",
+		"platform": "flsun_v400.stl",
+		"has_machine_quality": true,
+		"has_materials": true,
+		"machine_extruder_trains": {
+			"0": "flsun_v400_extruder_0"
+		},
+		"platform_offset": [
+			0,
+			-40.6455,
+			-43.5
+		]
+	},
+	"overrides": {
+		"gantry_height": {
+			"value": "0"
+		},
+		"infill_sparse_density": {
+			"default_value": 15
+		},
+		"machine_center_is_zero": {
+			"default_value": true
+		},
+		"machine_depth": {
+			"default_value": 300
+		},
+		"machine_end_gcode": {
+			"default_value": "END_PRINT\n"
+		},
+		"machine_head_with_fans_polygon": {
+			"default_value": [
+				[
+					0,
+					0
+				],
+				[
+					0,
+					0
+				],
+				[
+					0,
+					0
+				],
+				[
+					0,
+					0
+				]
+			]
+		},
+		"machine_heated_bed": {
+			"default_value": true
+		},
+		"machine_height": {
+			"default_value": 410
+		},
+		"machine_shape": {
+			"default_value": "elliptic"
+		},
+		"machine_start_gcode": {
+			"default_value": ";Nozzle diameter = {machine_nozzle_size}\n;Filament type = {material_type}\n;Filament name = {material_brand} {material_name}\n;Filament weight = {filament_weight}\n;M109 S{material_print_temperature}\n;M190 S{material_bed_temperature}\n\nSTART_PRINT BED_TEMP={material_bed_temperature_layer_0} EXTRUDER_TEMP={material_print_temperature_layer_0}\n"
+		},
+		"machine_width": {
+			"default_value": 300
+		},
+		"material_diameter": {
+			"default_value": 1.75
+		},
+		"z_seam_type": {
+			"value": "'sharpest_corner'"
+		}
+	}
 }

03-cura/01-configuration/extruders/flsun_v400_extruder_0.def.json

@@ -1,15 +1,56 @@
 {
-    "version": 2,
-    "name": "Extruder 1",
-    "inherits": "fdmextruder",
-    "metadata":
-    {
-        "machine": "flsun_v400",
-        "position": "0"
-    },
-    "overrides":
-    {
-        "extruder_nr": { "default_value": 0 },
-        "material_diameter": { "default_value": 1.75 }
-    }
+	"version": 2,
+	"name": "Extruder 1",
+	"inherits": "fdmextruder",
+	"metadata": {
+		"machine": "flsun_v400",
+		"position": "0"
+	},
+	"overrides": {
+		"extruder_nr": {
+			"default_value": 0
+		},
+		"material_diameter": {
+			"default_value": 1.75
+		},
+		"machine_nozzle_size": {
+			"default_value": 0.4
+		},
+		"material_max_temperature": {
+			"default_value": 300
+		},
+		"material_min_temperature": {
+			"default_value": 180
+		},
+		"material_flow": {
+			"default_value": 100
+		},
+		"retraction_enable": {
+			"default_value": true
+		},
+		"retraction_amount": {
+			"default_value": 0.8
+		},
+		"retraction_speed": {
+			"default_value": 35.0
+		},
+		"retraction_min_travel": {
+			"default_value": 1.5
+		},
+		"cool_fan_enabled": {
+			"default_value": true
+		},
+		"cool_fan_speed": {
+			"default_value": 80
+		},
+		"cool_min_layer_time": {
+			"default_value": 5
+		},
+		"speed_print": {
+			"default_value": 150
+		},
+		"speed_travel": {
+			"default_value": 250
+		}
+	}
 }

04-material/PLA+/SUNLU/black.md

@@ -4,7 +4,7 @@
 
 | Setting                                        | Value    |
 | :--------------------------------------------- | :------- |
-| Printing Temperature                           | 215°C    |
+| Printing Temperature                           | 213°C    |
 | Build Plate Temperature                        | 65°C     |
 | Flow                                           | 93.5%    |
 | Retraction Distance                            | 0.50mm   | ?

04-material/PLA+/SUNLU/white.md

@@ -0,0 +1,21 @@
+# PLA+ SUNLU Black
+
+## Settings
+
+| Setting                                        | Value    |
+| :--------------------------------------------- | :------- |
+| Printing Temperature                           | 216°C    |
+| Build Plate Temperature                        | 65°C     |
+| Flow                                           | 91.0%    |
+| Retraction Distance                            | mm   |
+| Retraction Speed                               | m/s   |
+| Retraction Extra Prime Amount                  | mm   |
+| Linear Advance Factor                          |      |
+
+## Prices
+
+https://www.amazon.de/gp/product/B07Y5K1TB5?psc=1
+
+| Date       | Price  |
+| :--------- | :----- |
+| 21.03.2025 | 15.99€ |